Home - Return to Previous Page
Click on image to zoom

Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB103Z590

631116
Performance Ceramic Brake Pads for Trucks and SUVs
Ultimate stopping power in an ultra-low dust, low noise ceramic compound!

Hawk Performance has introduced a premium, high performance, ultra-low dust, low noise compound called Performance Ceramic.

Performance Ceramic is engineered to reduce vehicle brake NVH (Noise, Vibration and Harshness), creating a quieter performing brake pad for your truck or SUV. Furthermore, the ceramic formula has a linear friction profile that allows your truck's ABS brake system to work more effectively. With Performance Ceramic you can expect reduced brake pad wear, lower dust output levels and a rotor-friendly brake pad.

Performance Ceramic � quiet, clean & fast stopping!

Key Features:
  • Increased stopping power
  • Increased rotor life
  • Extended pad life
  • Ultra-low dust
  • Extremely quiet
  • Stable friction output

    Recommended for import domestic automobiles, luxury SUV's, sports trucks & vans.

    Today's alloy wheel designs on premium vehicles has contributed to customer demand for a low dust performance brake product. Specify Hawk Performance's Performance Ceramic for your luxury car, SUV, or truck.

    All Hawk Performance Performance Ceramic brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.

    Note:
    Hawk Performance burnishes its Performance Ceramic brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against. Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
  • Was: $79.99
    Sale: $69.99
    Qty:

    Description

    Ultimate stopping power!
    Available in Front Pads
    Fits: 1979-1981 Pontiac Trans Am

    Installation

    Chevrolet Astro Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1989-2002 Chevrolet Astro Van 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Astro Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1985-1988 Chevrolet Astro Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Blazer Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1995-1997 Chevrolet Blazer Midsize with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Blazer Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1991 Chevrolet Blazer Fullsize with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Bonneville Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1981 Pontiac Bonneville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Brougham Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1995 Cadillac Brougham

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Camaro Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1981 Chevrolet Camaro

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Caprice Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1977-1989 Chevrolet Caprice

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Caprice Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1990-1996 Chevrolet Caprice Except Police & HD Models

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Catalina Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1981 Pontiac Catalina

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Century Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1977 Buick Century

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Chevelle Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1966-1977 Chevrolet Chevelle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac DeVille Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1984 Cadillac Deville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet El Camino Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1977 Chevrolet El Camino

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Eldorado Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1978 Cadillac Eldorado

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Electra Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1990 Buick Electra Wagon

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Electra Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1984 Buick Electra

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1978 Pontiac Firebird

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1979-1981 Pontiac Firebird

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Fleetwood Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1996-1996 Cadillac Fleetwood

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Fleetwood Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1985-1990 Cadillac Fleetwood Brougham

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1978 Pontiac Formula

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1979-1981 Pontiac Formula

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet G Series Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1995 Chevrolet G Series G10 / 1500 1/2 Ton Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet G Series Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1995 Chevrolet G Series G20 / 2500 3/4 Ton Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC G1500 Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1995 GMC G1500 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Jeep Grand Wagoneer Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1984-1991 Jeep Grand Wagoneer Full Size (J, MJ, & SJ Series)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Jimmy Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1991 GMC Jimmy Full Size

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick LeSabre Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1977-1985 Buick LeSabre

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Monte Carlo Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1970-1977 Chevrolet Monte Carlo

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Nova Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1979 Chevrolet Nova

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Parisienne Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1983-1989 Pontiac Parisienne

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Regal Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1977-1977 Buick Regal

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Regency Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1992 Oldsmobile Regency

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Riviera Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1978 Buick Riviera

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Roadmaster Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1991-1997 Buick Roadmaster

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Safari Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1989-2002 GMC Safari 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Safari Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1985-1988 GMC Safari

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Safari Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1983-1989 Pontiac Safari

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1995 GMC Savana 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1971-1995 GMC Savana 3/4 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Seville Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1976-1979 Cadillac Seville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Skylark Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1976-1979 Buick Skylark

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1981-1991 Chevrolet Suburban 1500 (1/2 Ton) - 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1990-1991 Chevrolet Suburban 1500 (1/2 Ton) - 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Toronado Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1972-1978 Oldsmobile Toronado & Trofeo

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1969-1978 Pontiac Trans Am

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB103Z590 Fits:
    1979-1981 Pontiac Trans Am

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Details

    Shipping Information

    • Item Requires Shipping
    • $24.99