Home - Return to Previous Page
Click on image to zoom

GMC Typhoon Hawk Performance Ceramic Brake Pads - HB119Z594

629436
Performance Ceramic Brake Pads for Trucks and SUVs
Ultimate stopping power in an ultra-low dust, low noise ceramic compound!

Hawk Performance has introduced a premium, high performance, ultra-low dust, low noise compound called Performance Ceramic.

Performance Ceramic is engineered to reduce vehicle brake NVH (Noise, Vibration and Harshness), creating a quieter performing brake pad for your truck or SUV. Furthermore, the ceramic formula has a linear friction profile that allows your truck's ABS brake system to work more effectively. With Performance Ceramic you can expect reduced brake pad wear, lower dust output levels and a rotor-friendly brake pad.

Performance Ceramic � quiet, clean & fast stopping!

Key Features:
  • Increased stopping power
  • Increased rotor life
  • Extended pad life
  • Ultra-low dust
  • Extremely quiet
  • Stable friction output

    Recommended for import domestic automobiles, luxury SUV's, sports trucks & vans.

    Today's alloy wheel designs on premium vehicles has contributed to customer demand for a low dust performance brake product. Specify Hawk Performance's Performance Ceramic for your luxury car, SUV, or truck.

    All Hawk Performance Performance Ceramic brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.

    Note:
    Hawk Performance burnishes its Performance Ceramic brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against. Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
  • Was: $77.99
    Sale: $67.99
    Qty:

    Description

    Ultimate stopping power!
    Available in Front Pads
    Fits: 1982-1993 GMC Typhoon

    Installation

    Pontiac Bonneville Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1986 Pontiac Bonneville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Bravada Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1991-1996 Oldsmobile Bravada

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Caballero Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1987 GMC Caballero

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Camaro Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Chevrolet Camaro with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Camaro Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Chevrolet Camaro with Rear Disc Brakes, Except 1LE Performance Package

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Camaro Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1988 Chevrolet Camaro

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Catalina Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1986 Pontiac Catalina

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Century Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1981 Buick Century

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Cutlass Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1987 Oldsmobile Cutlass

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Cutlass Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1988 Oldsmobile Cutlass (Except W Body)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet El Camino Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1987 Chevrolet El Camino

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Eldorado Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1979-1985 Cadillac Eldorado

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1988-1988 Pontiac Firebird with Rear Disc Brakes (2nd Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Firebird with Rear Disc Brakes (Except Perforance Package & Turbo)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Firebird with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Firebird Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1988 Pontiac Firebird with Rear Disc Brakes (1st Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Formula with Rear Disc Brakes (Except Perforance Package & Turbo)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1988-1988 Pontiac Formula with Rear Disc Brakes (2nd Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Formula with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Formula Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1988 Pontiac Formula with Rear Disc Brakes (1st Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Grand Prix Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1983-1987 Pontiac Grand Prix

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Grand Ville Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1986 Pontiac Grand Ville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Isuzu Hombre Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1996-1997 Isuzu Hombre

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Isuzu Hombre Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1998-2000 Isuzu Hombre 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Jimmy Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1996 GMC Jimmy Mid Size

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Jimmy Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1997-1997 GMC Jimmy Mid Size 4WD with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Jimmy Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1997-1997 GMC Jimmy Mid Size 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Malibu Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1983 Chevrolet Malibu

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Monte Carlo Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1988 Chevrolet Monte Carlo

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Regal Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1978-1987 Buick Regal

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Buick Riviera Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1979-1985 Buick Riviera

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet S10 Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1983-1997 Chevrolet S10 T10 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet S10 Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1983-1997 Chevrolet S10 Blazer 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet S10 Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1983-1997 Chevrolet S10 Blazer (T10) 4WD with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet S10 Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-2003 Chevrolet S10 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC S15 Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1990 GMC S15 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Seville Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1980-1985 Cadillac Seville

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sonoma Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1998-2004 GMC Sonoma 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sonoma Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1997 GMC Sonoma

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Syclone Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1992 GMC Syclone

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Oldsmobile Toronado Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1979-1985 Oldsmobile Toronado & Trofeo

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1988-1988 Pontiac Trans Am with Rear Disc Brakes (2nd Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1988 Pontiac Trans Am with Rear Disc Brakes (1st Design)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Trans Am with Rear Disc Brakes (Except Perforance Package & Turbo)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Pontiac Trans Am Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1989-1992 Pontiac Trans Am with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Typhoon Hawk Performance Ceramic Brake Pads - HB119Z594 Fits:
    1982-1993 GMC Typhoon

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Details

    Shipping Information

    • Item Requires Shipping
    • $24.99