Home - Return to Previous Page
Click on image to zoom

Volvo 260 Hawk HP Plus Brake Pads - HB172N595

631789
HP Plus / Autocross Brake Pads


Hawk Performance's HP Plus brake pad compound is ideal for Autocross and Track Day drivers looking for a high performance race compound that can take the heat of the track and get you home safely without having to change the pads.

HP Plus utilizes a unique Ferro-Carbon, high-tech friction material that was developed and manufactured for sport driving in autocross, Solo II and "track day" applications. The Ferro-Carbon formulation offers lower wear rates and higher torque values than other competitive materials.

Extremely high coefficient of friction makes HP Plus the perfect upgrade over stock for high performance streetcars used in autocross competition or that experience repetitive, heavy braking.

Key Features:
  • Extremely High Friction Output
  • Fade Resistant
  • Worthy for Autocross & Club Racing Events

    Warning! Due to the dramatic friction levels produced by this product to achieve "race-level" braking, rotor wear, noise, dust, and pad life may be affected.

    All Hawk Performance HP Plus / Autocross brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.

    Note:
    Hawk Performance burnishes its HP Plus brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against. Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
  • Was: $92.99
    Sale: $81.99
    Qty:

    Description

    Ideal for Autocross!
    Available in Front Pads
    Fits: 1975-1984 Volvo 260 with ATE Caliper

    Installation

    Volvo 240 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1984 Volvo 240 with ATE Caliper

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 240 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1985-1993 Volvo 240 242, 242, 245 (DL, GL, GLE, GLT, GT)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 740 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1991-1993 Volvo 740 with ABS

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 760 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1991-1993 Volvo 760 with ABS

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 780 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1993-1997 Volvo 780

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Porsche 924 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1976-1985 Porsche 924 (Except S, Sport, & Turbo Models)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 940 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1991-1991 Volvo 940 with ABS & Rear ATE Caliper (without IRS)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 940 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1992-1997 Volvo 940 with Rear ATE Caliper (without IRS)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 960 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1991-1991 Volvo 960 with ABS & Rear ATE Caliper (without IRS)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 960 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1992-1997 Volvo 960 with Rear ATE Caliper (without IRS)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo C70 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1999-2002 Volvo C70 with 15 Inch Wheels

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo C70 Hawk HP Plus Brake Pads - HB172N595 Fits:
    2003-2003 Volvo C70 Convertible

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300D

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300E

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300SD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300SE

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300SDL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1987 Mercedes-Benz S Class 300SEL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1986-1991 Mercedes-Benz S Class 420SE, SEL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1986-1991 Mercedes-Benz S Class 560 SEC, SEL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1990-1991 Mercedes-Benz S Class 350SD, SDL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1988-1991 Mercedes-Benz S Class 300SEL

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Mercedes-Benz S Class Hawk HP Plus Brake Pads - HB172N595 Fits:
    1988-1991 Mercedes-Benz S Class 300SE

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo S70 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1999-2000 Volvo S70 (For 15 Inch Wheels)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo V70 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1999-2000 Volvo V70 (For 15 Inch Wheels)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Volvo 260 Hawk HP Plus Brake Pads - HB172N595 Fits:
    1975-1984 Volvo 260 with ATE Caliper

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Details

    Shipping Information

    • Item Requires Shipping
    • $24.99