Home - Return to Previous Page
Click on image to zoom

GMC Yukon Hawk SuperDuty Brake Pads - HB323P724

629514
SuperDuty - Severe-Duty Truck Brake Pad Compound
Extreme Braking for Extreme Payloads

Hawk's SuperDuty Ferro-Carbon material is engineered for severe-duty professional truck fleets and trucks and SUVs towing heavy loads. This material offers unmatched braking performance under high inertia and/or repetitive braking applications.

To drive safely with heavy payloads it is critical to have brakes that operate properly. Heavy fleet trucks and light trucks and SUVs carrying heavy tow loads experience high braking temperatures. Higher temperatures contribute to premature brake pad and rotor wear. Hawk Performance's SuperDuty product is a sophisticated material that has an extremely high coefficient of friction designed to provide maximum truck and SUV stopping power with excellent high temperature heat dissipation.

Upgrade your fleet or tow vehicle's braking performance with Hawk Performance's SuperDuty, Sever-Duty compound!

Key Features:
  • Extremely high coefficient of friction
  • Extremely high fade resistance

    Recommended for professional fleets (greater than 1 ton) and light trucks towing excessive payloads.

    Superior high temperature rotor and pad wear performance.
  • Was: $124.99
    Sale: $108.99
    Qty:

    Description

    Extreme Braking for Extreme Payloads!
    Available in Front Pads
    Fits: 2003-2005 GMC Yukon XL 2WD

    Installation

    Chevrolet Astro Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 Chevrolet Astro Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 Chevrolet Avalanche 1500, Except Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Avalanche 1500 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 Chevrolet Avalanche 1500 with Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Avalanche 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Avalanche 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Avalanche Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2005 Chevrolet Avalanche 2500

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Blazer Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2003 Chevrolet Blazer Fullsize with Rear Disc Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Blazer Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2004-2005 Chevrolet Blazer Fullsize with Rear Disc Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Denali Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2000 GMC Denali

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2004-2004 Cadillac Escalade (Except 2WD)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Cadillac Escalade EXT

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2003 Cadillac Escalade with Rear Disc Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2005 Cadillac Escalade

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2004-2004 Cadillac Escalade 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 Cadillac Escalade EXT

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet G Series Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2006 Chevrolet G Series G10 / 1500 1/2 Ton Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC G1500 Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC G1500 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Safari Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Safari

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Savana 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Savana 3/4 Ton (7300lb GVW)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    1999-2000 GMC Sierra 1500 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 GMC Sierra 1500 4WD 2DR Regular Cab

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    1999-2000 GMC Sierra 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 GMC Sierra 1500 2WD 2DR

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2005 GMC Sierra 1500 4WD 2DR with 2 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2006 GMC Sierra 1500 2WD 2DR with 2 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Sierra 1500 2WD 2DR Extended Cab with 4 Wheel Steering (325mm Rear Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Sierra 1500 4WD 2DR Extended Cab with 4 Wheel Steering (325mm Rear Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 GMC Sierra 1500 4WD 2DR Extended Cab

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Sierra 1500 2WD 2DR Extended Cab with 4 Wheel Steering (330mm Rear Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 GMC Sierra 1500 4WD 2DR Extended Cab with 4 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 GMC Sierra 1500 2WD 2DR Extended Cab with 4 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Sierra 1500 4WD 2DR Extended Cab with 4 Wheel Steering (330mm Rear Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Sierra Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 GMC Sierra 2500

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    1999-2000 Chevrolet Silverado 1500 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    1999-2000 Chevrolet Silverado 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 Chevrolet Silverado 1500 2WD 2DR

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2004 Chevrolet Silverado 1500 4WD 2DR with 2 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Silverado 1500 2WD 2DR Extended Cab with 4 Wheel Steering (325 mm Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 Chevrolet Silverado 1500 4WD 2DR Regular Cab

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2004 Chevrolet Silverado 1500 2WD 2DR with 2 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2006-2006 Chevrolet Silverado 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Silverado 1500 4WD 2DR Extended Cab with 4 Wheel Steering (325mm Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 Chevrolet Silverado 1500 2WD 2DR Extended Cab with 4 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2001 Chevrolet Silverado 1500 4WD 2DR Extended Cab

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2006-2006 Chevrolet Silverado 1500 Hybrid

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Silverado 1500 2WD with Rear Drum

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Silverado 1500 4WD 2DR Extended Cab with 4 Wheel Steering (330mm Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Silverado 1500 2WD 2DR Extended Cab with 4 Wheel Steering (330mm Disc)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2002-2002 Chevrolet Silverado 1500 4WD 2DR Extended Cab with 4 Wheel Steering

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Silverado Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Silverado 2500

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Suburban 1500 (1/2 Ton) - 2WD - Rear Disc Brakes, without Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Suburban 1500 (1/2 Ton) - 4WD - Rear Disc Brakes, without Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Suburban 1500 (1/2 Ton) - 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Suburban 1500 (1/2 Ton) - 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Suburban 1500 (1/2 Ton) - 2WD - Rear Disc Brakes, With Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Suburban 1500 (1/2 Ton) - 4WD - Rear Disc Brakes, With Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Suburban 1500 (1/2 Ton) - 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2005 Chevrolet Suburban 2500 (3/4 Ton)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Suburban 1500 (1/2 Ton) - 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 Chevrolet Tahoe 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Tahoe 4WD - Rear Disc Brakes, without Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2004-2006 Chevrolet Tahoe 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2003 Chevrolet Tahoe 2WD - Rear Disc Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 Chevrolet Tahoe 4WD - Rear Disc Brakes, With Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 Chevrolet Tahoe 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 GMC Yukon XL without Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 GMC Yukon 4WD (Except XL) with Rear Disc Brakes (No Limited Slip Axle)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 GMC Yukon 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 GMC Yukon 4WD (Except XL) with Rear Disc Brakes & Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2000 GMC Yukon 2WD (Except XL & Performance Package) with Rear Disc Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 GMC Yukon XL 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2005-2006 GMC Yukon 4WD (Except XL)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2001-2002 GMC Yukon 2WD (Except XL)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 GMC Yukon XL 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2000-2002 GMC Yukon XL with Limited Slip Axle

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 GMC Yukon 4WD (Except XL)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2004 GMC Yukon 2WD (Except XL)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk SuperDuty Brake Pads - HB323P724 Fits:
    2003-2005 GMC Yukon XL 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Details

    Shipping Information

    • Item Requires Shipping
    • $24.99