Home - Return to Previous Page
Click on image to zoom

GMC Yukon Hawk Performance Ceramic Brake Pads - HB332Z654

629497
Performance Ceramic Brake Pads for Trucks and SUVs
Ultimate stopping power in an ultra-low dust, low noise ceramic compound!

Hawk Performance has introduced a premium, high performance, ultra-low dust, low noise compound called Performance Ceramic.

Performance Ceramic is engineered to reduce vehicle brake NVH (Noise, Vibration and Harshness), creating a quieter performing brake pad for your truck or SUV. Furthermore, the ceramic formula has a linear friction profile that allows your truck's ABS brake system to work more effectively. With Performance Ceramic you can expect reduced brake pad wear, lower dust output levels and a rotor-friendly brake pad.

Performance Ceramic � quiet, clean & fast stopping!

Key Features:
  • Increased stopping power
  • Increased rotor life
  • Extended pad life
  • Ultra-low dust
  • Extremely quiet
  • Stable friction output

    Recommended for import domestic automobiles, luxury SUV's, sports trucks & vans.

    Today's alloy wheel designs on premium vehicles has contributed to customer demand for a low dust performance brake product. Specify Hawk Performance's Performance Ceramic for your luxury car, SUV, or truck.

    All Hawk Performance Performance Ceramic brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.

    Note:
    Hawk Performance burnishes its Performance Ceramic brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against. Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
  • Was: $98.99
    Sale: $86.99
    Qty:

    Description

    Ultimate stopping power!
    Available in Front Pads
    Fits: 1998-2000 GMC Yukon 2WD (Except XL & Performance Package) with Rear Drum Brakes

    Installation

    Chevrolet Astro Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1989-2002 Chevrolet Astro Van 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Blazer Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-2000 Chevrolet Blazer Fullsize with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet K2500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1998 Chevrolet K2500 3/4 Ton 4WD - 7200lb GVW

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet C1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 Chevrolet C1500 1/2 Ton 2WD - Standard Cab / HD Chassis / Extended Cab / SS 454

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet C1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1999 Chevrolet C1500 1/2 Ton 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC C1500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 GMC C1500 2WD - Standard Cab HD Chassis, Extended Cab

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC C1500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1999 GMC C1500 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC C2500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1998 GMC C2500 2WD - 7200lb GVW

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC K1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 GMC K1500 4WD - 10 Inch Rear Drums, Standard Cab HD Chass, Extended Cab With Standard Chass

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC K1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 GMC K1500 4WD - 11 Inch Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC K1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1999 GMC K1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC K2500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1998 GMC K2500 4WD - 7200lb GVW

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet C2500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1998 Chevrolet C2500 3/4 Ton 2WD - 7200lb GVW

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac DeVille Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1990-1993 Cadillac Deville HD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac DeVille Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1998-1999 Cadillac Deville HD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Escalade Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1999-2000 Cadillac Escalade with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Cadillac Fleetwood Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1991-1992 Cadillac Fleetwood HD FWD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet G Series Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1996-2002 Chevrolet G Series G10 / 1500 1/2 Ton Van

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet G Series Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1996-2002 Chevrolet G Series G20 / 2500 3/4 Ton Van (7300LB GVW)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC G1500 Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1996-2002 GMC G1500 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet K1500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 Chevrolet K1500 1/2 Ton 4WD - 10 Inch Rear Drums, Standard Cab HD Chass, Extended Cab With Standard Chass.

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet K1500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1988-1991 Chevrolet K1500 1/2 Ton 4WD - 11 Inch Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet K1500 Pickup Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1999 Chevrolet K1500 1/2 Ton 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Dodge Ram Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1994-1999 Dodge Ram 1500 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Safari Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1989-2002 GMC Safari 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1996-2002 GMC Savana 1/2 Ton

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Savana Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1996-2002 GMC Savana 3/4 Ton (7300lb GVW)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1993 Chevrolet Suburban 1500 (1/2 Ton) - 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1994-2000 Chevrolet Suburban 1500 (1/2 Ton) - 2WD - 11 Inch Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-1993 Chevrolet Suburban 1500 (1/2 Ton) - 4WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Suburban Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1994-2000 Chevrolet Suburban 1500 (1/2 Ton) - 4WD - 11 Inch Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1995-2000 Chevrolet Tahoe 4WD - Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1995-1997 Chevrolet Tahoe 2WD

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    Chevrolet Tahoe Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1998-2000 Chevrolet Tahoe 2WD - Except Police & Performance Package - Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1995-1997 GMC Yukon 2WD (Except XL)

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1992-2000 GMC Yukon 4WD (Except XL) with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Installation

    GMC Yukon Hawk Performance Ceramic Brake Pads - HB332Z654 Fits:
    1998-2000 GMC Yukon 2WD (Except XL & Performance Package) with Rear Drum Brakes

    Brake Pad Installation Procedure
    1. Install brake pads properly. Be sure pads are securely positioned in the caliper.

    2. Flush system with fresh brake fluid.

    3. Check all hydraulic parts for excess wear and tear.

    4. Check disc for proper thickness, parallelism, and lateral runout.

    5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.

    6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.

    7. Inspect calipers for freedom of movement. Lubricate where necessary.

    Burnishing Instructions
    1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.

    2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.

    3. Be sure to not drag brakes!

    4. Allow 15 minutes for brake system to cool down.

    5. After step 4 your new pads are ready for use.

    Details

    Shipping Information

    • Item Requires Shipping
    • $24.99